ports:start
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionNext revisionBoth sides next revision | ||
ports:start [2018/12/06 11:11] – created support | ports:start [2019/01/02 11:50] – support | ||
---|---|---|---|
Line 1: | Line 1: | ||
**__Question: | **__Question: | ||
- | **__Answer: | + | **__Answer: |
+ | |||
+ | On some installations of Windows 10 or with some updates installed, the firewall seems to block some ports used by the Control software to communicate with the other software (Local and/or trough network). | ||
+ | This makes it unable to configure or control the mixer. \\ | ||
+ | |||
+ | This can be solved by changing some of these port numbers. \\ | ||
+ | |||
+ | Sometimes with trying to find the right ones that are open. \\ | ||
+ | |||
+ | Keep in mind that the Remote host should be the local host 127.0.0.1 or when sharing data with a secong pc the ip address of the computer where the mixer is connected to. \\ | ||
+ | |||
+ | ==== Step 1 (The Configuration manager) ==== | ||
+ | |||
+ | Uncheck the Use defaults setting in the Control and Configuration manager. \\ | ||
+ | |||
+ | For transmitting the configuration to the Mixer the Green port is used (Software to mixer). \\ | ||
+ | |||
+ | The Red port is for reading the settings and Firmware version from the Mixer (Mixer to Software). \\ | ||
+ | |||
+ | If one of these ports are blocked it isn’t possible to use the configuration tool. \\ | ||
+ | Mostly when changing the Green port to a higher unused number like 19552 this will be fixed. \\ | ||
+ | |||
+ | ==== Keep in mind to stop the connection and re start! ==== | ||
- | {{: | ||
{{: | {{: | ||
+ | |||
+ | ==== Step 2 (The meters) ==== | ||
+ | |||
+ | In blue you’ll see the port that is used for transmitting the data to control the On switches with the software. | ||
+ | (Software to Mixer). \\ | ||
+ | |||
+ | In orange you’ll see the port that is used for transmitting the meter data to the meters. | ||
+ | (Mixer to Software). \\ | ||
+ | |||
+ | NOTE: Some PC’s with Windows 10 experience problems with meters losing the connection for a short time. \\ | ||
+ | In Windows 7 this happens in a lower frequency and when you restart the PC it will run fine for a certain time. \\ | ||
+ | It is caused by the usb handling of the operating system and is also visible in the Airlite Control software. \\ | ||
+ | This can be solved by setting the power saving options of the usb to as less saving as possible or possibly playing with changing the port settings. \\ | ||
+ | |||
{{: | {{: | ||
+ | |||
+ | ==== Step 3 (The Virtual Keyboard Mapper or Playout software) ==== | ||
+ | |||
+ | For the control surface and fader start functions to control you’re playout software like in this example the Virtual Keyboard Mapper. \\ | ||
+ | This will be the same in Aircast or other supported playout software. \\ | ||
+ | |||
+ | The Green port is used to send the LED status data to the Airlite (Software to Mixer).\\ | ||
+ | |||
+ | The Red port is used for transmitting the Fader start or Button press status to the Software (Mixer to Software).\\ | ||
+ | |||
{{: | {{: | ||
+ | |||
+ | ===Keep in mind that when you change the IP address or these ports you’ll have to change them in all the used software!=== | ||
+ | |||
+ | ==== Step 4 (Overview and extra information) ==== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | * [[https:// | ||
+ | |||
+ | ==== Step 5 ==== | ||
+ | |||
+ | If the software still doesn' | ||
+ | |||
+ | [[https:// |
ports/start.txt · Last modified: 2022/07/18 09:02 by support